India
Compliance International is accredited to test the following interfaces:
ER Test Parameters for IP Conformance CONFIP - Router
Test Standards
- TCP Parameters Set-C as per Test 7. Annex-P12
- StaticRouting as per Test 6. Annex-P12
- DynamicRouting as per Test 5. Annex-P12
- IPV4 Parameters Set-E as per Test 2. Annex-P12
- Managability as per SNMP V2 or V3 as per Test 3, 4. Annex-P12
ER Test Parameters for IP Conformance CONFIP - L2 Switch
Test Standards
- Mac Learning and Packet Forwarding as per Test 2. Annex-P11
- Spanning Tree Protocol as per Test 3,4 Annex-P11
- "IPV4 Parameters Set-E as per Test 2. Annex-P12"
- Manageability SNMP V2 or V3 as per Test 5, 6 Annex-P11
ER Test Parameters for IP Conformance CONFIP - L3 Switch
Test Standards
- Mac Learning and Packet Forwarding as per Test 2. Annex-P11
- Spanning Tree Protocol as per Test 3,4 Annex-P11
- "IPV4 Parameters Set-E as per Test 2. Annex-P12"
- Manageability SNMP V2 or V3 as per Test 5, 6 Annex-P11
- Static routing as per Test 9. Annex-P11
- Dynamic Routing as per Test 8. Annex-P11
ER Test Parameters for ISDN BRI Conformance CONFISDN BRI
Test Standards
- Layer-III BRI Specification - Call Clearing as per Q.931. Annex-D1
- Layer-III BRI Specification - Call Setup as per Q.931. Annex-D1
ER Test Parameters for ISDN PRI Conformance CONFISDN PRI
Test Standards
- Layer-III PRI Specification - Call Clearing as per Q.931. Annex-D1
- Layer-III PRI Specification - Call Setup as per Q.931. Annex-D1
ER Test Parameters for SS7 Conformance CONFSS7
Test Standards
- CCS7 MTP2 Parameters as per ITU-T Q.781. Annex-D3
- CCS7 MTP3 Parameters as per ITU-T Q.782. Annex-D3
- CCS7 ISUP Parameters as per ITU-T Q.784. Annex-D3
ER Test Parameters for products having or conne table to 2W Interface INT 2W
Test Standards
- Idle State Current for 2 wire Int as per ETSI EN 300 001 and TBR-21 Clause 4.4.1. Annex-D
- Insulation Test for 2 wire Int as per ETSI EN 300 001. Annex-D
- Longitudinal Conversion Loss 2-W Int as per Q.552 Clause 2.1.1.2. Annex-D
- Maximum Loop Current for 2W Int as per ETSI EN 300 001. Annex-D
- Return Loss for 2W Int as per Q.552 Clause 2.1.1.2. Annex-D
- Transmission of DTMF signalling as per Q.23 Clause 6 and 7. Annex-D
ER Test Parameters for products having Ethernet Interfaces INTETH (1G Optical)
Test Standards
- Average Launch power for 1 GE Opt as per IEEE 802.3z Clause 38. Annex-H
- Receiver Sensitivity 1 GE Opt as per IEEE 802.3z Clause 38. Annex-H
- Wavelength for 1 GE Opt as per IEEE 802.3z Clause 38. Annex-H
ER Test Parameters for products having Ethernet Interfaces INTETH (10G Optical)
Test Standards
- Average Launch power for 10 GE Opt as per IEEE 802.3ae Clause 52. Annex-H
- Receiver Sensitivity 10 GE Opt as per IEEE 802.3ae Clause 52. Annex-H
- Wavelength for 10 GE Opt as per IEEE 802.3ae Clause 52. Annex-H
ER Test Parameters for products having Ethernet Interfaces INTETH (40G Optical)
Test Standards
- Average Launch power for 40 GE Opt as per IEEE 802.3ba Clause 86, 87. Annex-H
- Receiver Sensitivity 40 GE Opt as per IEEE 802.3ba Clause 86, 87. Annex-H
- Wavelength for 40 GE Opt as per IEEE 802.3ba Clause 86, 87. Annex-H
ER Test Parameters for products having Ethernet Interfaces INTETH (100G Optical)
Test Standards
- Average Launch power for 100 GE Opt as per IEEE 802.3ba Clause 86, 88. Annex-H
- Receiver Sensitivity 100 GE Opt as per IEEE 802.3ba Clause 86, 88. Annex-H
- Wavelength for 100 GE Opt as per IEEE 802.3ba Clause 86, 88. Annex-H
ER Test Parameters for products having Ethernet Interfaces INTETH (FE & GE Electrical)
Test Standards
- Link Speed and Autonegotiation Test FE as per IEEE 802.3. Annex-H
- Link Speed and Autonegotiation Test GE as per IEEE 802.3. Annex-H
ER Test Parameters for products having PDH Interfaces INTPDH (E1)
Test Standards
- Bit Rate Tolerance 2 MBPS Int as per G.703 Clause 11.1 or ETSI-TBR-4 Clause B.2.3. Annex-I
- Input Jitter Tolerance for 2 MBPS Int as per G.823, ETSI-TBR-4 Clause 9.3.3. Annex-I
- Input Return Loss for 2 MBPS Int as per G.703 Clause 11.3, ETSI-TBR Clause 9.3.1. Annex-I
- Output Jitter for 2 MBPS Int as per G.823/l.431 OR ETSI-TBR-4. Annex-I
- Pulse Mask for 2 MBPS Int as per G.703 Cl. 11.2 of 4/2014, TBR-4 Cl. 9.2.1. Annex-I
ER Test Parameters for products having PDH Interfaces INTPDH (E3)
Test Standards
- Bit Rate Tolerance 34 MBPS Int as per G.703 Clause 13.1. Annex-I
- Input Jitter Tolerance for 34 MBPS Int as per G.823. Annex-I
- Input Return Loss for 34 MBPS Int as per G.703. Annex-I
- Output Jitter for 34 MBPS Int as per G.823. Annex-I
- Pulse Mask for 34 MBPS Int as per G.703. Annex-I
ER Test Parameters for products having PDH Interfaces INTPDH (DS3)
Test Standards
- Bit Rate Tolerance 45 MBPS Int as per G.703 Clause 10. Annex-I
- Input Jitter Tolerance for 45 MBPS Int as per G.824. Annex-I
- Input Return Loss for 45 MBPS Int as per G.703. Annex-I
- No DC power as per G.703. Annex-I
- Pulse Mask for 45 MBPS Int as per G.703. Annex-I
- Output Jitter for 45 MBPS Int as per G.824. Annex-I
ER Test Parameters for products having SDH Interfaces INTSDH (STM-1 Opt)
Test Standards
- Bit Rate Tolerance STM-1 Opt Int as per G.957. Annex-K
- Input Jitter Tolerance for STM-1 Opt as per G.825. Annex-K
- Mean Launched Power for STM-1 Opt Int as per G.957. Annex-K
- Operating Wavelength for STM-1 Opt Int as per G.957. Annex-K
- Output Jitter for STM-1 Opt Int as per G.825.Annex-K
- Receiver Sensitivity for STM-1 Opt Int as per G.957. Annex-K
- Receiver Overload for STM-1 Opt Int as per G.957. Annex-K
ER Test Parameters for products having SDH Interfaces INTSDH (STM-4 Opt)
Test Standards
- Bit Rate Tolerance STM-4 Opt Int as per G.957. Annex-K
- Input Jitter Tolerance for STM-4 Opt as per G.825. Annex-K
- Mean Launched Power for STM-4 Opt Int as per G.957. Annex-K
- Operating Wavelength for STM-4 Opt Int as per G.957. Annex-K
- Output Jitter for STM-4 Opt Int as per G.825.Annex-K
- Receiver Sensitivity for STM-4 Opt Int as per G.957. Annex-K
- Receiver Overload for STM-4 Opt Int as per G.957. Annex-K
ER Test Parameters for products having SDH Interfaces INTSDH (STM-16 Opt)
Test Standards
- Bit Rate Tolerance STM-16 Opt Int as per G.957. Annex-K
- Input Jitter Tolerance for STM-16 Opt as per G.825. Annex-K
- Mean Launched Power for STM-16 Opt Int as per G.957. Annex-K
- Operating Wavelength for STM-16 Opt Int as per G.957. Annex-K
- Output Jitter for STM-16 Opt Int as per G.825.Annex-K
- Receiver Sensitivity for STM-16 Opt Int as per G.957. Annex-K
- Receiver Overload for STM-16 Opt Int as per G.957. Annex-K
ER Test Parameters for products having SDH Interfaces INTSDH (STM-64 Opt)
Test Standards
- Bit Rate Tolerance STM-64 Opt Int as per G.709. Annex-K
- Input Jitter Tolerance for STM-64 Opt as per G.825. Annex-K
- Mean Launched Power for STM-64 Opt Int as per G.691. Annex-K
- Operating Wavelength for STM-64 Opt Int as per G.957. Annex-K
- Output Jitter for STM-64 Opt Int as per G.783. Annex-K
- Receiver Overload for STM-64 Opt Int as per G.691. Annex-K
- Receiver Sensitivity for STM-64 Opt Int as per G.691. Annex-K
ER Test Parameters for Products having PON Interfaces INT PON (GPON)
Test Standards
- Operating Wavelength Recv for GPON Int as per G.984.2. Annex-J
- Operating Wavelength Trans for GPON Int as per G.984.2. Annex-J
- Opt Output Power for GPON Int at OLT as per G.984.2. Annex-J
- Opt Output Power for GPON Int at ONT as per G.984.2. Annex-J
- Receiver Sensitivity for GPON Int at OLT as per G.984.2. Annex-J
- Receiver Sensitivity for GPON Int at ONT as per G.984.2. Annex-J
ER Test Parameters for Products having PON Interfaces INT PON (EPON)
Test Standards
- Operating Wavelength Recv for EPON Int as per IEEE 802.3ah. Annex-J
- Operating Wavelength Trans for EPON Int as per IEEE 802.3ah. Annex-J
- Opt Output Power for EPON Int at OLT as per IEEE 802.3ah. Annex-J
- Opt Output Power for EPON Int at ONT as per IEEE 802.3ah. Annex-J
- Receiver Sensitivity for EPON Int at OLT as per IEEE 802.3ah. Annex-J
- Receiver Sensitivity for EPON Int at ONT as per IEEE 802.3ah. Annex-J
ER Test Parameters for Products having PON Interfaces INT PON (XGPON)
Test Standards
- Operating Wavelength Recv for XGPON Int as per G.987.2. Annex-J
- Operating Wavelength Trans for XGPON Int as per G.987.2. Annex-J
- Opt Output Power XGPON Int at OLT as per G.987.2. Annex-J
- Opt Output Power XGPON Int at ONT as per G.987.2. Annex-J
- Receiver Sensitivity XGPON Int at OLT as per G.987.2. Annex-J
- Receiver Sensitivity XGPON Int at ONT as per G.987.2. Annex-J
ER Test Parameters for Products having PON Interfaces INT PON (XGSPON)
Test Standards
- Operating Wavelength Recv XGSPON Int as per G.9807.1. Annex-J
- Operating Wavelength Trans XGSPON Int as per G.9807.1. Annex-J
- Opt Output Power XGSPON Int at OLT as per G.9807.1. Annex-J
- Opt Output Power XGSPON Int at ONT as per G.9807.1. Annex-J
- Receiver Sensitivity XGSPON Int at OLT as per G.9807.1. Annex-J
- Receiver Sensitivity XGSPON Int at ONT as per G.9807.1. Annex-J
ER Test Parameters for Products having PON Interfaces INT PON (WDMPON)
Test Standards
- Operating Wavelength Trans WDMPON Int as per G.694.1. Annex-J
- Operating Wavelength Trans WDMPON Int as per G.694.1. Annex-J
- Opt Output Power WDMPON Int at OLT as per G.694.1. Annex-J
- Opt Output Power WDMPON Int at ONT as per G.694.1. Annex-J
- Receiver Sensitivity WDMPON Int at OLT as per G.694.1. Annex-J
- Receiver Sensitivity WDMPON Int at ONT as per G.694.1. Annex-J
ER Test Parameters for Products having PON Interfaces INT PON (NGPON)
Test Standards
- Operating Wavelength Recv NGPON Int as per G.989.2. Annex-J
- Operating Wavelength Trans NGPON Int as per G.989.2. Annex-J
- Opt Output Power NGPON Int at OLT as per G.989.2. Annex-J
- Opt Output Power NGPON Int at ONT as per G.989.2. Annex-J
- Receiver Sensitivity NGPON Int at OLT as per G.989.2. Annex-J
- Receiver Sensitivity NGPON Int at ONT as per G.989.2. Annex-J
ER Test Parameters for Products having OTN Interfaces INTOTU (OTU-1)
Test Standards
- Bit Rate Tolerance OTU-1 Int as per G.709 Clause 7.3. Annex-L
- Central Frequency for OTU-1 as per G.959.1 clause 7.2.2.3 and G.694.1. Annex-L
- Input Jitter Tolerance for OUT-1 Int as per G.8251. Annex-L
- Mean Total Input Power for OTU-1 as per G.959.1, G.693. Annex-L
- Mean Total Output Power for OTU-1 as per G.959.1, G.693. Annex-L
- Minimum Receiver Overload for OTU-1 as per G.959.1, G.695. Annex-L
- Receiver Sensitivity for OTU-1 Int as per G.959.1, G.693. Annex-L
ER Test Parameters for Products having OTN Interfaces INTOTU (OTU-2)
Test Standards
- Bit Rate Tolerance OTU-2 Int as per G.709 Clause 7.3. Annex-L
- Central Frequency for OTU-2 as per G.959.1 clause 7.2.2.3 and G.694.1. Annex-L
- Input Jitter Tolerance for OUT-2 Int as per G.8251. Annex-L
- Mean Total Input Power for OTU-2 as per G.959.1, G.693. Annex-L
- Mean Total Output Power for OTU-2 as per G.959.1, G.693. Annex-L
- Minimum Receiver Overload for OTU-2 as per G.959.1, G.693. Annex-L
- Receiver Sensitivity for OTU-2 Int as per G.959.1, G.693. Annex-L
ER Test Parameters for Products having OTN Interfaces INTOTU (OTU-3)
Test Standards
- Bit Rate Tolerance OTU-3 Int as per G.709 Clause 7.3. Annex-L
- Central Frequency for OTU-3 as per G.959.1 clause 7.2.2.3 and G.694.1. Annex-L
- Mean Total Input Power for OTU-3 as per G.959.1, G.693. Annex-L
- Mean Total Output Power for OTU-3 as per G.959.1, G.693. Annex-L
- Minimum Receiver Overload for OTU-3 as per G.959.1, G.693. Annex-L
- Receiver Sensitivity for OTU-3 Int as per G.959.1, G.693. Annex-L
ER Test Parameters for Products having OTN Interfaces INTOTU (OTU-4)
Test Standards
- Bit Rate Tolerance OTU-4 Int as per G.709 Clause 7.3. Annex-L
- Central Frequency for OTU-4 as per G.959.1 clause 7.2.2.3 and G.694.1. Annex-L
- Mean Total Input Power for OTU-4 as per G.959.1, G.695. Annex-L
- Mean Total Output Power for OTU-4 as per G.959.1, G.695. Annex-L
- Minimum Receiver Overload for OTU-4 as per G.959.1, G.695. Annex-L
- Receiver Sensitivity for OTU-4 Int as per G.959.1, G.693. Annex-L